TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) XO006 by GPM  [XO006]

TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006
Price:
USD$23.90
Brand:
GPM
Model:
XO006
GTIN:
4894538035292
Condition:
Brand New
2 Reviews
Write a review
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"
alt="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006" title="TRAXXAS Xo-1 Aluminium Wheel Hex Claw (0mm) - 2pcs - GPM XO006"

Precision aluminium hex claw for Xo-1 hubs

The XO006 aluminium wheel hex claw is a precision-engineered replacement intended to interface with TRAXXAS Xo-1 wheel hubs. Supplied as a matched pair, these CNC-friendly aluminium claws maintain a 0mm offset and provide a repeatable mounting surface for accurate wheel positioning on Xo-1 assemblies.

Service technicians should remove the wheel and existing hex, inspect hub seating and bearing tolerances, then fit the aluminium claw in the correct orientation using factory hardware. Use calibrated torque for the hex fasteners and verify radial runout to maintain alignment and wheel balance.

As an upgrade and replacement component this part improves long-term consistency in wheel mounting geometry. The aluminium construction delivers stable reference faces for setup measurements such as toe and camber, and is suitable for repeat fitment during maintenance cycles.

Specifications

  • Item Aluminium Wheel Hex Claw (0mm) - 2 pcs
  • Material Aluminium
  • Model Number XO006
  • Compatibility TRAXXAS Xo-1

XO006 is supplied for precise 0mm offset wheel mounting on TRAXXAS Xo-1 hubs; confirm bearing and hub fit during installation to ensure consistent performance.

 

Product Reviews
2 Reviews
rating
Just finished building a 4-tec 2.0 with GPM parts. SOOO beautiful. After having a bad experience building a wltoys this summer it was nice to once again do another build using GPM parts. The website is nothing to brag about but, the parts are top quality.
rating
Once again it was a pleasure dealing with GPM customer service to inquire about a part. GPM was able to fill my order in a timely manner. Excellent communication from customer service. Thanks GPM!

What inspection steps are recommended before fitting?

Check hub bore diameter, bearing play, and mating face for burrs; clean components and use correct hardware orientation to ensure precise seating.

Is any machining required to fit?

No machining should be necessary for compatible Xo-1 hubs; if interference is found, investigate hub wear or bearing seating rather than altering the hex claw.

Recommended assembly practice?

Use measured torque values, verify runout on a spin fixture, and recheck wheel geometry on-vehicle after a short test run to confirm stability.

When should I replace the hex claw?

Replace when you observe deformation, excessive wear, or loss of accurate seating that affects wheel alignment or balance.