TRAXXAS Unlimited Desert Racer Front CVD Precision Upgrade UDR096FS by GPM  [UDR096FS]

TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS
Price:
USD$33.90
Brand:
GPM
Model:
UDR096FS
GTIN:
4894538303360
Condition:
Brand New
Write a review
alt="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS" title="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS"
alt="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS" title="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS"
alt="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS" title="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS"
alt="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS" title="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS"
alt="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS" title="TRAXXAS UNLIMITED DESERT RACER Extra Duty Front CVD With SST Joint And Harden Steel Body - 2pc set - GPM UDR096FS"

Precision front CVD solution for Unlimited Desert Racer

This front CVD assembly is engineered for TRAXXAS Unlimited Desert Racer models as a direct aftermarket replacement for standard dogbones, focusing on durability and consistent torque transfer. The design combines an SST joint with a hardened steel body to minimise deflection under load while retaining the vehicle's original driveline geometry.

The kit includes two matched front CVD halves intended to integrate with existing driveline components. Dimensional specifications are maintained at a 96mm midpoint dogbone length with an extra duty diameter range of 4.5mm to 6.5mm to ensure correct fit and alignment.

Installation follows standard front CVD procedures: remove stock dogbones, attach CVD halves to axle and hub interfaces, torque SST joint fasteners to spec, and verify spline engagement and suspension clearance. Routine inspection of fasteners and spline contact is recommended to sustain optimal performance.

Specifications

  • Item: Extra Duty Front CVD with SST Joint and Harden Steel Body - 2pcs set
  • Material: Hardened steel body, SST joint components
  • Model Number: UDR096FS
  • Compatibility: TRAXXAS UNLIMITED DESERT RACER

Specifically suited for hobbyists seeking a robust, dimensionally accurate front CVD upgrade to reduce drivetrain flex and extend service intervals.

What inspection steps are recommended after installation?

Confirm spline engagement, check for free suspension travel, and verify that SST joint fasteners are torqued and secured with thread locker where appropriate.

Are these components serviceable?

Yes, the joint and CVD halves can be inspected and serviced; replace worn components promptly to preserve alignment and performance.

What should I watch for in aggressive use?

Monitor for unusual wear on splines and joint faces after extended high-load runs and ensure seals and clearances remain intact to prevent debris ingress.

Which measurements confirm correct fitment?

Verify the 96mm midpoint dogbone length and confirm the 4.5-6.5 diameter interfaces align with your stock axle hubs to ensure correct geometry and engagement.