TRAXXAS Telluride 4x4 Precision Aluminium Main Shaft TEL025 technical upgrade by GPM  [TEL025]

TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025
Price:
USD$18.90
Brand:
GPM
Model:
TEL025
GTIN:
4894538121735
Condition:
Brand New
Write a review
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"
alt="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025" title="TRAXXAS TELLURIDE 4x4 Aluminium Main Shaft With Hard Steel Ends - 1pc set - GPM TEL025"

Precision aluminium main shaft with hardened terminations

This aluminium main shaft fitted with hardened steel end fittings is supplied as an aftermarket replacement for TRAXXAS Telluride 4x4 models. The configuration pairs a lightweight aluminium shaft body with hardened steel terminations to ensure wear concentrates at replaceable interfaces with gears and bearings, supporting longer service intervals and predictable wear patterns.

Supplied as a single pcs component, the part is intended to fit the Telluride 4x4 platform noted in the specifications. Professional installation requires removal of the gearbox or axle housing to access the original main shaft, accurate shaft exchange, and verification of gear mesh and bearing alignment. Fine adjustments to spur and pinion spacing or bearing preload are often necessary to restore nominal drivetrain clearance and minimise noise.

During assembly ensure the hardened ends are fully seated in the bearing bores and that axial play is controlled within manufacturer tolerance. Conduct an initial low-load run to verify smooth rotation and absence of endplay or binding. Scheduled inspections of the hardened terminations and adjacent bearings will identify early wear and protect downstream gear components.

Specifications

  • Item: Main shaft
  • Material: Aluminium shaft with hard steel ends
  • Model Number: TEL025
  • Compatibility: TRAXXAS Telluride 4x4

Recommended for technicians and experienced hobbyists replacing worn shafts or upgrading drivetrain durability on TRAXXAS Telluride 4x4 models; validate fit and mesh during installation.

This item is compatible with

  • TRAXXAS TELLURIDE 4X4

What inspections are critical before final assembly?

Confirm bearing inner diameters, housing runs, and shaft seating. Replace any bearings with radial play to prevent premature wear of the hardened ends.

Are spacer or shims required during fitment?

Depending on gearbox variant, thin shims may be used to set correct pinion/spur mesh or to eliminate axial play; measure and adjust incrementally.

How often should the hardened ends be checked?

Inspect them after the first few runs post-install and then at regular maintenance intervals, especially after abrasive or wet running conditions.

Does TEL025 require break-in?

A gentle break-in under light load is recommended to confirm alignment and to seat bearings; validate mesh and check for unusual noise before full-power operation.