Traxxas Slash Rear Widened CVD Drive Shaft with Knuckle Arm SSLA1277RH22 by GPM  [SSLA1277RH22]

TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22
Price:
USD$63.90
Brand:
GPM
Model:
SSLA1277RH22
GTIN:
4894538305739
Condition:
Brand New
Write a review
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22"
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22"
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22"
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22"
alt="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22" title="TRAXXAS 1/10 Slash 4x4 Steel+Aluminium Widen Rear CVD Drive Shaft W. Knuckle Arm - 12pc set - GPM SSLA1277RH22"

Precision widened rear CVD for Slash applications

This rear CVD drive shaft assembly is a 12pcs kit designed for Traxxas Slash platforms. The assembly couples hardened 45# steel CVD internals with 6061 T6 aluminium interfaces to provide a balance of tensile strength and reduced mass for demanding short course conditions.

Technical summary: the CVD uses hardened 45# steel mated to 6061 T6 aluminium, knuckle arms are CNC-style 6061 T6 aluminium, and the axle is increased to a 6mm cross section to improve resistance to bending and impact loads. A spring-steel hex is specified to maintain secure torque transfer and the supplied bearings are chosen to minimise friction under radial and axial loads.

Included component summary as supplied: CVD + hex ×2 pcs, rear knuckle arm ×2 pcs, bearing 6x13x5 ×4 pcs, screw pin M4x2.5x11 ×2 pcs, set screw 3x3 ×2 pcs. The kit is intended for straightforward replacement or to support bespoke rebuilds with OEM-compatible interfaces.

Compatible Models

  • Traxxas Slash 4x4
  • Slash 4x4 Low CG
  • Slash Pro 2WD Short Course

Use this assembly when increased rear driveline durability and predictable handling under impact are required; validate fitment to your specific Slash variant prior to installation.

What machining tolerances are relevant for fit?

Ensure hub bores and hex fits are within expected OEM tolerances; check bearing seat runout and hex engagement to avoid premature wear.

Can the 6mm axle be used with heavy-duty shocks and spring rates?

Yes, the thicker axle improves resistance to bending under high-energy landings typical of stiffer suspension setups, though whole-drivetrain compliance should be assessed.

What maintenance extends service life?

Regular inspection of hex retention, bearing end float and fastener torque combined with periodic bearing lubrication will extend component life under competitive use.

Are replacement bearings available in the same spec?

Use 6x13x5 bearings of equivalent quality for replacements to retain designed clearances and load distribution characteristics.

Is the spring-steel hex serviceable or replaceable?

The spring-steel hex can be replaced if worn; inspect for deformation and replace with like-for-like components to maintain torque transfer and retention properties.