Rear Stub Axle Carrier Upgrade RUS4022N - Precision 7075 Alloy by GPM  [RUS4022N]

TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N
Price:
USD$19.90
Brand:
GPM
Model:
RUS4022N
GTIN:
4894538389050
Condition:
Brand New
Write a review
alt="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N" title="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N"
alt="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N" title="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N"
alt="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N" title="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N"
alt="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N" title="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N"
alt="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N" title="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N"
alt="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N" title="TRAXXAS RUSTLER VXL 7075 Alloy Rear Stub AXLE Carriers - GPM RUS4022N"

Precision 7075 Rear Stub Axle Carriers

This aluminium rear stub axle carrier set is engineered as an aftermarket upgrade for selected TRAXXAS 1/10 4x4 platforms. The carriers are machined from 7075 alloy to combine reduced component weight with improved tensile strength at the rear lower and upper arm junctions and the axle interface.

Bearing bores accept 5x13x4 bearings in a tightened seat to limit axial and radial play. Minimised bearing clearance improves hub alignment under acceleration, cornering and variable load, helping maintain consistent rear-wheel rotation.

Installation notes: carriers are designed for direct replacement on the listed TRAXXAS models and will commonly reuse original fasteners and bearings where applicable. During reassembly confirm correct bearing orientation and preload, verify driveshaft and linkage clearance, and torque fasteners evenly.

Packing includes

  • Rear stub axle carriers - 2pcs
  • Bearing 5x13x4 - 4pcs

Original Name / Part No:

1952

Compatible Models

  • TRAXXAS 1/10 RUSTLER 4X4 VXL-67076-4
  • TRAXXAS 1/10 4WD HOSS 4X4 VXL 3S-90076-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74064-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74054-4
  • TRAXXAS 1/10 Nitro Rustler-44096-3
  • TRAXXAS 1/10 Nitro Slash-44056-3
  • TRAXXAS 1/10 Rustler 4X4-67064-1
  • TRAXXAS 1/10 Rustler 4X4-67064-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68086-4
  • TRAXXAS 1/10 Slash 4X4-68054-1
  • TRAXXAS 1/10 Slash 4X4-68054-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68286-4
  • TRAXXAS 1/10 Stampede 4X4 VXL-67086-4
  • TRAXXAS 1/10 Rustler 4X4 Ultimate-67097-4
  • TRAXXAS 1/10 Slash 4X4 Ultimate-68277-4

Use these precision machined carriers to reduce rear hub play and restore consistent bearing alignment on compatible TRAXXAS 1/10 4x4 models.

Are the bearing sizes and quantities included in the kit specified?

The kit includes two aluminium carriers and four 5x13x4 bearings as listed in the packing includes section.

Which assembly checks are recommended for correct fitment?

Verify square seating of bearings, check for minimal lateral play, confirm driveshaft and linkage clearance throughout suspension travel, and torque fasteners to even values.

What advantage does 7075 alloy give in a rear carrier application?

7075 alloy provides higher tensile strength than many common aluminium grades, helping resist deformation in load-bearing junctions while keeping weight moderate.

Is any special lubrication required for the included bearings?

Use a light bearing lubricant suited to 5x13x4 bearings; avoid heavy greases that can attract grit and increase rolling resistance.