Mini-Z AWD Rear Knuckle Arm Holder, Precision Alloy 0.6mm Plate, Toe Out -0.2mm MZA031R-0206 by GPM  [MZA031R-0206]

Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206
Price:
USD$4.80
Brand:
GPM
Model:
MZA031R-0206
GTIN:
4894538121902
Condition:
Brand New
Write a review
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"

Engineered alloy rear knuckle arm holder for Mini-Z AWD

This alloy rear knuckle arm holder is supplied as a single replacement for Kyosho Mini-Z AWD rear knuckles. The component establishes a -0.2mm rear Toe Out and employs a 0.6mm thick alloy plate to maintain repeatable alignment under typical running loads.

Use this part where consistent rear geometry and predictable toe settings are required for setup work. Confirm part orientation and mating surface contact during installation to preserve accurate alignment and wheel clearance throughout suspension travel.

Installation checklist: align the holder to the knuckle, torque fasteners to recommended values, inspect for full suspension travel clearance, and perform a road or track check to validate handling response. Package quantity: 1 pcs.

Will this holder change baseline geometry significantly?

No. The -0.2mm specification is a small, fixed adjustment intended for fine tuning rather than wholesale geometry changes.

What checks should I perform after fitting?

Verify fastener torque, confirm seating of the holder on the knuckle, and cycle the suspension to check for rubbing or binding at full travel.

Is the thickness compatible with common Mini-Z setups?

At 0.6mm the plate offers a balance of stiffness and compatibility, but confirm against your specific knuckle and spacer arrangement to ensure correct fit.