GPM AXIAL SCX10 III Body-Side Stainless Tread Trim SCX3ZSP11 Set  [SCX3ZSP11]

AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11
Price:
USD$18.90
Brand:
GPM
Model:
SCX3ZSP11
GTIN:
4894538345056
Condition:
Brand New
Write a review
alt="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11" title="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11"
alt="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11" title="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11"
alt="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11" title="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11"
alt="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11" title="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11"
alt="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11" title="AXIAL Racing SCX10 III JEEP WRANGLER Stainless Steel Slip Proof Tread - 34pc set - GPM SCX3ZSP11"

Stainless scale tread panels - technical overview

This 34-piece decorative tread kit is produced for the AXIAL SCX10 III JEEP WRANGLER body sides and is intended as scale trim only. It does not substitute structural or mechanical components on the vehicle.

The kit includes the full set for both sides: 8 stainless slip-proof tread plates and 26 pcs 1.2M screws, totalling 34 pieces. Each plate features an engraved stainless finish for authentic scale texture, and a length of 3M double-sided tape is supplied for precise trial positioning prior to final fixing with screws.

Installation guidance: align the tread plates on the body sides, use the 3M tape to secure temporary placement, then fasten with the supplied 1.2M screws where the body allows. These components are decorative and will not affect suspension, steering, or drivetrain systems.

Compatible Models

  • AXIAL-SCX10 III JEEP WRANGLER-AXI03007

A precision stainless body-side detailing kit for AXIAL SCX10 III JEEP WRANGLER, supplying engraved treads, adhesive tape and screws for accurate scale installation.

What is the recommended fitting sequence for best alignment?

Clean the body surface, position each tread plate using the 3M tape to check alignment, then progressively secure with 1.2M screws starting from the centre of each plate to avoid distortion.

Are the screw holes sized to match the supplied fasteners?

Yes, the tread plates are prepared to accept the included 1.2M screws for a correct fit between plate and body panel.

How should I preserve the engraved finish after use?

Wipe off mud and grit after runs and avoid abrasive cleaners; light polishing with a soft cloth will maintain the engraved detail without damaging the finish.

Is this kit compatible with modified SCX10 III bodies?

Compatibility can vary with heavily modified shells; trial-fit with the 3M tape and make minor trimming where needed to achieve proper placement.