AXIAL SCX10 II Precision Centre Shaft SSCX27037 by GPM  [SSCX27037]

AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037
Price:
USD$33.90
Brand:
GPM
Model:
SSCX27037
GTIN:
4894538259070
Please kindly input your name and email address, we will inform you once we have the restocking.
Write a review
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"
alt="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037" title="AXIAL Racing SCX10 II Steel+Aluminium Center Shaft (S:118mm-128mm, L:130mm-140mm) - 1set - GPM SSCX27037"

Precision engineered centre shaft for SCX10 II

The SSCX27037 centre shaft set is engineered as a replacement assembly for AXIAL Racing SCX10 II models. The configuration pairs hardened steel in bearing and joint interfaces with machined aluminium sections to lower rotational mass while maintaining load-bearing integrity.

This combination reduces drivetrain torque requirements at low speeds and improves driveline response during articulation. The parts are dimensioned for compatibility with SCX10 II suspension geometry and intended for a direct-fit installation by experienced technicians and advanced hobbyists.

The set includes small hardware for mounting: M4*2.5*11 screw shaft - 4pcs, 4*2.5 O-ring - 4pcs.

Compatible Models

  • Axial SCX-10 II AX

Use SSCX27037 when a precision, lighter centre driveline component is required for scale crawling on SCX10 II builds, and apply regular inspection and lubrication schedules after installation.

What tolerances should I expect from SSCX27037?

Manufactured to tight dimensional tolerances appropriate for SCX10 II fitment; verify shaft lengths S:118mm-128mm and L:130mm-140mm against your parts during installation.

Which areas are steel versus aluminium?

Steel is specified for contact and bearing zones to resist wear, while aluminium is used on rotating members to lower mass; this balances durability and dynamic performance.

Any special assembly notes?

Use a medium-strength thread locker on fasteners if appropriate, check alignment during assembly, and confirm there is no binding through full suspension articulation.

Recommended maintenance schedule?

Inspect joint play and seal condition after initial break-in and then at regular intervals depending on use; lubricate steel to aluminium contact areas with a compatible product.