56T Carbon Steel Spur Gear SSLA2W056T Technical Upgrade by GPM  [SSLA2W056T]

TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T
Price:
USD$18.90
Brand:
GPM
Model:
SSLA2W056T
GTIN:
4894538365818
Condition:
Brand New
Write a review
alt="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T" title="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T"
alt="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T" title="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T"
alt="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T" title="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T"
alt="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T" title="TRAXXAS FORD F-150 SVT RAPTOR OBA Carbon Steel Spur Gear(56T) - 4pc set - GPM SSLA2W056T"

Precision 56T carbon steel spur for TRAXXAS 1/10

This 1/10-scale 56-tooth, 0.8 module spur gear is engineered for driveline installation in compatible TRAXXAS 2WD models. CNC machined from hardened black carbon steel to tight tolerances, the component provides increased wear resistance and consistent tooth engagement compared with polymer spurs. It is intended for rear gearbox fitment where it transmits drive from the pinion into the drivetrain with minimal backlash when installed correctly.

The package includes the main 56T spur gear plus three stainless steel washers for axial spacing; the gear retains a robust 0.8 module profile and is manufactured to align with the listed TRAXXAS 1/10 2WD models. Recommended assembly steps: verify tooth contact using a marker, use the supplied washers to set endplay, inspect bearings, and ensure appropriate gearbox lubrication to protect mating surfaces.

Packing includes

  • Spur Gear 56T - 1pcs
  • Stainless Steel Washer 3*7*0.2 - 3pcs

Original Name / Part No:

4690,4683,4686

Compatible Models

  • TRAXXAS-1/10 ELECTRIC 2WD F-150 SVT RAPTOR-58064-2
  • TRAXXAS-1/10 2WD BANDIT XL-5 BUGGY-24054-1
  • TRAXXAS-1/10 2WD BANDIT XL-5 BUGGY-24054-61
  • TRAXXAS-1/10 2WD BANDIT XL-5 BUGGY-24054-4
  • TRAXXAS-1/10 2WD BANDIT VXL BRUSHLESS BUGGY-24076-74
  • TRAXXAS-1/10 2WD BANDIT VXL BRUSHLESS BUGGY-24076-4
  • TRAXXAS-1/10 2WD SLASH SHORT COURSE TRUCK-58014-4
  • TRAXXAS-1/10 2WD SLASH SHORT COURSE TRUCK-58024
  • TRAXXAS-1/10 2WD SLASH SHORT COURSE TRUCK-58034-1
  • TRAXXAS-1/10 2WD SLASH SHORT COURSE TRUCK-58034-61
  • TRAXXAS-1/10 2WD SLASH VXL SHORT COURSE TRUCK-58076-74
  • TRAXXAS-1/10 2WD SLASH VXL SHORT COURSE TRUCK-58076-4

Use this hardened carbon steel 56T spur for a direct nylon-to-steel drivetrain upgrade on compatible TRAXXAS 1/10 2WD models; confirm pinion pitch and clearances prior to high-load operation.

Which models require mesh shims when fitting this gear?

Use the included stainless steel washers to set axial spacing. Specific mesh may vary by chassis and pinion; measure contact patch across several teeth and add or remove washers to achieve even engagement.

How should I inspect machining quality on arrival?

Visually inspect tooth edges and bore for burrs or nicks, verify concentricity on a mandrel if available, and lightly deburr any sharp flash before fitting to prevent premature pinion wear.

What lubrication strategy is recommended?

Apply a light, gearbox-compatible grease to bearings and sliding surfaces; avoid heavy surface films on tooth faces that can trap grit and accelerate wear.

Will using a steel spur require pinion replacement more often?

Pinion wear depends on material hardness and mesh quality. Inspect the pinion after initial runs and replace if tooth profiles show rounding or scoring to protect both components.